Cisco
Exam 100-101
Cisco Interconnecting Cisco Networking Devices Part 1 (ICND)
Version: Demo
[ Total Questions: 10 ]
Topic Break Down
Topic 3, IP addressing (IPv4 / IPv6)
Question No : 1 - (Topic 3)
Which one of the following IP addresses is the last valid host in the subnet using mask 255.255.255.224?
A. 192.168.2.63
B. 192.168.2.62
C. 192.168.2.61
D. 192.168.2.60
E. 192.168.2.32
Answer: B
Topic 6, Network Device Security
Question No : 2 - (Topic 6)
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Answer: E
Question No : 3 - (Topic 6)
How can you ensure that only the MAC address of a server is allowed by switch port Fa0/1?
A. Configure port Fa0/1 to accept connections only from the static IP address of the server.
B. Configure the server MAC address as a static entry of port security.
C. Use a proprietary connector type on Fa0/1 that is incomputable with other host connectors.
D. Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.
Answer: B
Question No : 4 - (Topic 6)
A company has placed a networked PC in a lobby so guests can have access to the corporate directory.
A security concern is that someone will disconnect the directory PC and re-connect their laptop computer and have access to the corporate network. For the port servicing the
lobby, which three configuration steps should be performed on the switch to prevent this?
(Choose three.)
A. Enable port security.
B. Create the port as a trunk port.
C. Create the port as an access port.
D. Create the port as a protected port.
E. Set the port security aging time to 0.
F. Statically assign the MAC address to the address table.
G. Configure the switch to discover new MAC addresses after a set time of inactivity.
Answer: A,C,F
Topic 7, Troubleshooting
Question No : 5 - (Topic 7)
Select three options which are security issues with the current configuration of SwitchA. (Choose three.)
A. Privilege mode is protected with an unencrypted password
B. Inappropriate wording in banner message
C. Virtual terminal lines are protected only by a password requirement
D. Both the username and password are weak
E. Telnet connections can be used to remotely manage the switch
F. Cisco user will be granted privilege level 15 by default
Answer: A,B,D
Question No : 6 - (Topic 7)
Refer to the exhibit.
A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can
be made about this design?
A. This design will function as intended.
B. Spanning-tree will need to be used.
C. The router will not accept the addressing scheme.
D. The connection between switches should be a trunk.
E. The router interfaces must be encapsulated with the 802.1Q protocol.
Answer: C
Topic 8, OSPF Questions
Question No : 7 - (Topic 8)
What information can be used by a router running a link-state protocol to build and maintain its topological database?
(Choose two.)
A. hello packets
B. SAP messages sent by other routers
C. LSAs from other routers
D. beacons received on point-to-point links
E. routing tables received from other link-state routers
F. TTL packets from designated routers
Answer: A,C
Question No : 8 - (Topic 8)
What command sequence will configure a router to run OSPF and add network 10.1.1.0
/24 to area 0?
A. router ospf area 0
network 10.1.1.0 255.255.255.0 area 0
B. router ospf
network 10.1.1.0 0.0.0.255
C. router ospf 1
network 10.1.1.0 0.0.0.255 area 0
D. router ospf area 0
network 10.1.1.0 0.0.0.255 area 0
E. router ospf
network 10.1.1.0 255.255.255.0 area 0
F. router ospf 1
network 10.1.1.0 0.0.0.255
Answer: C
Question No : 9 - (Topic 8)
Refer to the exhibit.
Which two statements are true about the loopback address that is configured on RouterB?
(Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Answer: B,C
Topic 9, Simulation
Question No : 10 CORRECT TEXT - (Topic 9)
There are three locations in a school district of a large city: ROUTER -M, ROUTER -W and ROUTER -U. The network connection between two of these locations has already functioned. Configure the ROUTER -M router IP addresses on the E0 and S0 interfaces so that the E0 receives the first usable subnet while the S0 receives the second usable subnet from the network 192.168.160.0/28. Both interfaces would receive the last available ip address on the proper subnet.
NotE. The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process.
Answer: ROUTER-M> enable
PassworD. Cisco
ROUTER-M# config t
ROUTER-M(config)# interface e0
ROUTER-M(config-if)# ip address 192.168.160.14 255.255.255.240
ROUTER-M(config-if)# no shutdown
ROUTER -M(config-if)# exit
ROUTER -M(config)# interface s0
ROUTER-M(config-if)# ip address 192.168.160.30 255.255.255.240
ROUTER-M(config-if)# no shutdown
ROUTER-M(config-if)# end
ROUTER-M# copy run start
No comments:
Post a Comment